Work in progress: OPEN THE BOLEX: Difference between revisions
Jump to navigation
Jump to search
| Line 76: | Line 76: | ||
=Open the mechanism= | =Open the mechanism= | ||
<gallery> | |||
File:Open the mechanism 00.jpg|00 | |||
File:Open the mechanism 01.jpg|01 | |||
File:Open the mechanism 02.jpg|02 | |||
File:Open the mechanism 03.jpg|03 | |||
File:Open the mechanism 04.jpg|04 | |||
File:Open the mechanism 05.jpg|05 | |||
File:Open the mechanism 06.jpg|06 | |||
File:Open the mechanism 07.jpg|07 | |||
File:Open the mechanism 08.jpg|08 | |||
File:Open the mechanism 09.jpg|09 | |||
File:Open the mechanism 10.jpg|10 | |||
File:Open the mechanism 11.jpg|11 | |||
File:Open the mechanism 12.jpg|12 | |||
File:Open the mechanism 13.jpg|13 | |||
File:Open the mechanism 14.jpg|14 | |||
File:Open the mechanism 15.jpg|15 | |||
File:Open the mechanism 16.jpg|16 | |||
File:Open the mechanism 17.jpg|17 | |||
File:Open the mechanism 18.jpg|18 | |||
File:Open the mechanism 19.jpg|19 | |||
File:Open the mechanism 20.jpg|20 | |||
File:Open the mechanism 21.jpg|21 | |||
File:Open the mechanism 22.jpg|22 | |||
File:Open the mechanism 23.jpg|23 | |||
File:Open the mechanism 24.jpg|24 | |||
File:Open the mechanism 25.jpg|25 | |||
File:Open the mechanism 26.jpg|26 | |||
File:Open the mechanism 27.jpg|27 | |||
File:Open the mechanism 28.jpg|28 | |||
File:Open the mechanism 29.jpg|29 | |||
</gallery> | |||
Revision as of 14:43, 24 October 2026
open the BOLEX introduction
Manuals
How to use
who we are
index
A_Pressure-Pad-Blade
B_Claw
C_Turret
.jpg)
Turret check
There must be no misalignment between the base and the turret. Some turrets are bent because the lens is too heavy. C-Mount RX lenses, when focused at infinity, produce a sharp image 17.5mm beyond the end of the thread. Always use RX lenses for Bolex Rex cameras, as other lenses produce a sharp image at 15mm. These can only be used when filming close up (not at infinity).
D_Variable shutter
E_Camera body
F_Upper Base plate
G_Lower base plate
H_Motor spring Winding mechanism
IT_Mechanism
J_Frame counter
K_Speed governor
L_Loop-former
M_Lid-Rewinding handle
N_Leathering
O_Viewfinders
P_Eye-level focus
Q_RX-Viewfinder
Shutter timing
issues or trouble shooting
Basic check procedure
- Observe the outside aspect of the camera.
- Check the prism, if there are any scratches or fingerprints.
- Check shutter timing
- Check spring motor:
- put on 24fps, run with different fps, but load a test film when you run with 48 or 64fps.
- Winding up more than 21 rounds
- Listen to the sound, if the sound slowing down, means the dust is inside the plate and dried out lubrication
- holding the take up, to see if the take up is running
- Check how many seconds is fully winded, between 24-27 seconds
- Check if the counter is working
- Check the turret if it is flat on the plate, if it is distorted, perhaps by heavy lens
Open the mechanism
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
